Finally the long awaited stuffed/plush dinosaur (brontosaur (Apatosaurus) vs diplodocus continues!) tutorial with sewing pattern! I've wanted a dino plushie/stuffie for a long time so I made three! :)
Edit:
Click here to see Dino's people have made with this tutorial. Thanks everyone!
For this project you will need:
- Paper pattern pieces cut from the Stuffed Dinosaur sewing pattern Page 1 of 2 and Stuffed Dinosaur sewing pattern Page 2 of 2. To print properly to a full A4 you need to Download the images then print them. Each of these pattern pieces is an A4 or standard letter size sheet. Join the sheets along the dotted line and cut the pattern pieces. A seam allowance of 0.5cm (1/4 inch) is given, add more if you like.
- Fabric- I used good old quilting cotton here but any non-stretchy material will do, although heavier upholstery type fabrics will be harder to turn right side out. Use a fun contrasting fabric for the scales along the back or even a multitude of colours.
- 1 pair safety eyes- these are easy to find in craft store, fabric stores and on the net but you could replace them with felt eyes, fabric paint eyes, buttons etc.
- Stuffing- I used fibre fill but old pillow stuffing, sewing scraps etc could be substituted
- Scissors
- Thread
To begin:
Cut all your pattern pieces like so-
Note the blue scales at the bottom are two pieces of fabric each. For the scales I used three of the larger scales, two of the medium and one of the smallest. Remember to cut two of the sides of the bodies and only 1 of the underside of the body. You'll need four of the circles for the pads of the feet.
With the fabric wrong sides together, sew the all scales along four sides only, leaving the bottom edge unsewn to enable turning right side out, as shown below:
This seam allowance is only 0.5 of a cm else the scales get too bulky. At each corner snip away the fabric as shown so that the corners are pointy when we turn them right sides out.
Turn all the scales right sides out (and press with an iron if you wish) and place to one side.
Next take the underside of the body piece and fold the leg sections towards the middle of the piece. Then sew a shallow arc as shown in the photo- this will enable the legs to stand underneath the body instead of splaying out to the side. Do this for each leg. Do not worry if there is not very much left of the "belly" material left. It'll work.
Next by matching up the leg pieces and starting at the feet sew the underside of the body to the side of the body. Note- DO NOT sew up the bottom of the feet. The photo below shows the three seams- front leg to chin, back of front leg to front of back leg and finally back leg to underside tail. Also note that the underside body only reaches to the chin and stops before the end of the tail.
Sew the other side body to the piece created above using the same method of starting at one of the legs. Here is a detail shot of what should happen at the the tail. It looks very similar at the chin. DO NOT at this stage sew along the back or around the head, Only sew the underside of the body to the side pieces. Not the side pieces to each other.
Another detail look at those legs before sewing all together- as you can see the arcs on the lower body will make those legs sections shorter. That is OK! Since I can't regulate how shallow or deep your arcs will be this is variable so I made the legs the same length and you can trim them to the same length.
That is the underside of the body complete.
Take your scales and line them along your dinosaurs back. I placed mine largest to smallest.
Flip each of the scales towards the inside of the body, sandwiching each scale between the side body pieces. Pin these in place since they tend to move about.
I didn't get any photo's of the next few steps.
Sew the body closed by starting at the chest where the underside of the body piece ends, around the head and to the tail. The only opening should be the undersides of the feet. Sew three of the four feet circles into three of the four leg tubes to complete them. For help on this see "Making the Feet" in the
Baby Elephant Tutorial. Use the remaining open foot to turn the dinosaur the right way around.
At this point I loosely stuff just the head to get a feel for it and mark where I want the eyes to be. Then I remove the stuffing and insert the safety eyes according to their instructions. You can skip this step if painting or sewing on the eyes later
Beginning at the head and tip of the tail stuff the dinosaur firmly. If he is too soft his neck will flop from side to side. Once the stuffing is completed sew the last foot pad circle into the last open leg to close it.
That's it! Make an army of colourful dinosaurs and have a congratulatory cup of tea!
(The dino on the left was my prototype is a slightly different shape)
Please leave me a comment if you liked this project or, if you've made one, I'd love a link and perhaps I'll show it to everyone else in an update! Happy sewing!
PS Two of these Dinosaurs are available in the
Little Black Teapot Shop
Edit: Here is a quick sketch of how I close up the seams that are left using a whip stitch:
The "right side" of the fabric is the patterned side and the wrong is the other side. I have shown where the thread goes using dots but the dotty art will not be seen.
Hope this helps :)
